Yarr
Active Member
I figured i would start a new thread as my old one well. is a different tank all together
The tank is a 6 x 2 x 2 all glass tank with 2 corner overflows. I have made a sump for it out of my old 4 foot tank and am in the process of making the stand, which i am desperately trying to find motivation to get into at the moment. It is hard because of a issue with my other tank killing all the fish in it.... so yeh.. stuggling to stay the course
The stand itself will be custom made by myself using dressed pine. THe height i am aiming for will be quite high. so basically one can stand there and view it as opposed to making your visitors bend over to see whats inside. I think i have found soem tricky ways of making the stand which i will detail in pictures as i progress through the project.
Equipment wise i am at an ends atm. Becuase equipment is INSANELY expensive in Australia I have to be quite careful about what money i invest where and to get the right thing to do the job in the first place. I had some very bad advice when i first got into the hobby which i am exponentially wiser from now. I will be making my own maifold with nozzles located around the top of the tank.
I have decided against a spraybar setup mainly due to the fact that if i dont get the flwo right it will create too much back pressur eon the pump impellar and shorten its life, that of the bearing and create excess noise, heat and load on the motor.
The return pump is a RK2 Systems pump. It is meant to be quite quiet and especially made for aquarium applications as opposed to modified spa ( er.. decussi ??? ) pumps. It is a External 1/8 hp 10,800 L/h @ 2m. With this amount of flow The only other pump i might have inside the display itself would be a Tuzne 6080 8,500 L/h Stream, mainly to keep the water circulating in any deadspots i may find.
Skimming will be taken care of by a Aqua Medic Turboflotor shorty 5000. From memory it is rated up to 1200 L but i have seen it on systems up to 1500 L and it works without fault. I am still undecided at what height in the sump i will place this at the moment. There is no guidlines in the manual or any online resources i can find so far so i will experiement a bit when it gets in there. It will be fed froma bypass line from one of the overflows to the sump. The Skimme has its over Ocean Rrunner 3500 pump with needle wheel impeller to get things moving.
Sump... The sump is an old all glass 4 foot tank i hae runnign for a while. i added 4 baffles and built in a small fuge. I have the skimmer sitting in there at the momeny on a star board platform i have for it but i am taking that out and sitting it on the bottom as stated in the previous paragraph. If i need to bring the hiether up i will re make a platform using glass. as i have found the silicone bonds to it better than it does board - glass. I made a slight error when i made it in the fact tha ti got the hole in the side for the return pump drilled too low. so i will ahv eto get another sheet of glass cut and drilled at the correct height. barring that i coudl build up the height of the sump in the stand to match. I will see how that goes. The fuge will be fed from a pump in the sump and will house pretty much just macro.. if i cna ever find any decent non noxious stuff in this country. I plan on using a small light. like the one i have over my reptile enclosure. I think at this stage i will keep the light on constantly to get the macro feeding and growing liek crazy. i will see how that goes though.
Chiller. I have not decided on a chiller yet as i am still trying to work out what i will require. my 100 gal sits on 28 Deg C at the moment with 3 x 4 foot fluros. So as soon as i add the proper lighting for this tank i will definately run into heat problem. i just dont know how much heat and how it will affect a larger water volume with more surface area and more flow. Ambient temperature here is usually 32 Deg C almost all year around with high humidity in rainy season getting up to 94 %. To make matters worse and mor euncertain i will be posted to another locality at some stage and will most likely be a lot cooler in climate ( shudder ), So i am after a unit that heats aswell a cools. with high day time temps and low night time temps i dont want a massive swing in temps even though i am aware this does infact occur naturally.
Lighting. I plan on using 3 x 250 W MH combo with actinic PC or fluro. The MIN cost of these here would be over $2,000 for the VERY base models. Not much more info than that i guess... um. yeh.. lights.. bright.. hot.. good
Additional equipment will be maybe a UV sterilizer but i knwo they are inbuilt into some chillers so i will look for it here.. Calcium reactor which i will have to add later.
The tank itself with be an all round reef with a mixutre of different corals and fish. I will be running a 3 inch sandbed and will hopefulyl have a MUCH easier time than i did with my 100 Gal.
Pictures to follow.......... soon ( tm )
The tank is a 6 x 2 x 2 all glass tank with 2 corner overflows. I have made a sump for it out of my old 4 foot tank and am in the process of making the stand, which i am desperately trying to find motivation to get into at the moment. It is hard because of a issue with my other tank killing all the fish in it.... so yeh.. stuggling to stay the course
The stand itself will be custom made by myself using dressed pine. THe height i am aiming for will be quite high. so basically one can stand there and view it as opposed to making your visitors bend over to see whats inside. I think i have found soem tricky ways of making the stand which i will detail in pictures as i progress through the project.
Equipment wise i am at an ends atm. Becuase equipment is INSANELY expensive in Australia I have to be quite careful about what money i invest where and to get the right thing to do the job in the first place. I had some very bad advice when i first got into the hobby which i am exponentially wiser from now. I will be making my own maifold with nozzles located around the top of the tank.
I have decided against a spraybar setup mainly due to the fact that if i dont get the flwo right it will create too much back pressur eon the pump impellar and shorten its life, that of the bearing and create excess noise, heat and load on the motor.
The return pump is a RK2 Systems pump. It is meant to be quite quiet and especially made for aquarium applications as opposed to modified spa ( er.. decussi ??? ) pumps. It is a External 1/8 hp 10,800 L/h @ 2m. With this amount of flow The only other pump i might have inside the display itself would be a Tuzne 6080 8,500 L/h Stream, mainly to keep the water circulating in any deadspots i may find.
Skimming will be taken care of by a Aqua Medic Turboflotor shorty 5000. From memory it is rated up to 1200 L but i have seen it on systems up to 1500 L and it works without fault. I am still undecided at what height in the sump i will place this at the moment. There is no guidlines in the manual or any online resources i can find so far so i will experiement a bit when it gets in there. It will be fed froma bypass line from one of the overflows to the sump. The Skimme has its over Ocean Rrunner 3500 pump with needle wheel impeller to get things moving.
Sump... The sump is an old all glass 4 foot tank i hae runnign for a while. i added 4 baffles and built in a small fuge. I have the skimmer sitting in there at the momeny on a star board platform i have for it but i am taking that out and sitting it on the bottom as stated in the previous paragraph. If i need to bring the hiether up i will re make a platform using glass. as i have found the silicone bonds to it better than it does board - glass. I made a slight error when i made it in the fact tha ti got the hole in the side for the return pump drilled too low. so i will ahv eto get another sheet of glass cut and drilled at the correct height. barring that i coudl build up the height of the sump in the stand to match. I will see how that goes. The fuge will be fed from a pump in the sump and will house pretty much just macro.. if i cna ever find any decent non noxious stuff in this country. I plan on using a small light. like the one i have over my reptile enclosure. I think at this stage i will keep the light on constantly to get the macro feeding and growing liek crazy. i will see how that goes though.
Chiller. I have not decided on a chiller yet as i am still trying to work out what i will require. my 100 gal sits on 28 Deg C at the moment with 3 x 4 foot fluros. So as soon as i add the proper lighting for this tank i will definately run into heat problem. i just dont know how much heat and how it will affect a larger water volume with more surface area and more flow. Ambient temperature here is usually 32 Deg C almost all year around with high humidity in rainy season getting up to 94 %. To make matters worse and mor euncertain i will be posted to another locality at some stage and will most likely be a lot cooler in climate ( shudder ), So i am after a unit that heats aswell a cools. with high day time temps and low night time temps i dont want a massive swing in temps even though i am aware this does infact occur naturally.
Lighting. I plan on using 3 x 250 W MH combo with actinic PC or fluro. The MIN cost of these here would be over $2,000 for the VERY base models. Not much more info than that i guess... um. yeh.. lights.. bright.. hot.. good
Additional equipment will be maybe a UV sterilizer but i knwo they are inbuilt into some chillers so i will look for it here.. Calcium reactor which i will have to add later.
The tank itself with be an all round reef with a mixutre of different corals and fish. I will be running a 3 inch sandbed and will hopefulyl have a MUCH easier time than i did with my 100 Gal.
Pictures to follow.......... soon ( tm )