November 1960 Electronics World
Table
of Contents
Wax nostalgic about and learn from the history of early electronics. See articles
from
Electronics World, published May 1959
 December 1971. All copyrights hereby acknowledged.

The fundamentals of
ClassB pushpull amplifiers have not changed since 1960 when
this article appeared in Electronics World magazine. The transistors for
making them have improved in most cases, but the design procedures are basically
the same. ClassB amplifiers, in case you are not familiar with the topology, are
able to amplify zeroreferenced sinusoidal signals throughout the full 360 degrees
of rotation signals without an offset voltage bias; they are constructed from two
ClassA amplifiers in a cascode configuration. Issues like crossover distortion
and thermal runaway are discussed in the amplifier design procedure.
PushPull Class B Transistor PowerOutput Circuits
By Walter H. Buchsbaum / Industrial Consultant,
Electronics World
Simple design procedure that will help to understand this very useful and popular
transistorized circuitry.
Transistor audio amplifiers have many advantages over their vacuumtube counterparts,
but one circuit that really highlights these advantages is the Class B pushpull
power amplifier. The great efficiency and simplicity of transistors really shine
in this application. With no filament power required and a relatively low "B+" voltage,
the power drain during quiet periods is negligible and the overall circuit efficiency
extremely high. These are certainly very desirable features.
Another attraction is the price of germanium power transistors which compares
favorably with vacuum tubes. In this article a typical 8watt amplifier design,
which uses transistors costing about $3.00 each, will be illustrated. The same design
procedure can be used for amplifiers at other power levels and for different transistor
types. Those readers who are more concerned with troubleshooting transistor audio
amplifiers will find the material helpful in understanding the sources of the most
frequent defects they are apt to find in transistor circuits.
Class B operation means that each transistor will amplify only onehalf of the
signal and will "rest" while its mate amplifies the oppositepolarity portion of
the signal. Because power dissipation is one of the most critical factors in transistors,
Class B operation is particularly suited to the task of insuring low dissipation
for each transistor. There are only two drawbacks to this type of transistor circuit:
crossover distortion and thermal runaway. These will be discussed below.
Crossover distortion occurs when one transistor stops conducting before the other
has started and is a typical problem with all Class B circuits. Thermal runaway
can occur in any transistor application but power transistors are especially susceptible.
This trouble is due to the fact that, as a transistor heats up, it will tend to
draw more current which, in turn, will cause the collector to heat up even more
until the unit burns out. There are wellestablished and relatively simple cures
for both crossover distortion and thermal runaway and they will be described here
in some detail. Let us first consider the characteristic curves.
Most of our readers will be somewhat familiar with the characteristic curves
used in vacuumtube circuit design. Similar curves are furnished by transistor manufacturers
and are used in the same manner. In last month's article on Class A transistor poweroutput
circuits we described some of the special aspects of transistor characteristic curves,
a discussion which will not be repeated here. Instead, we will concentrate on the
design of a typical amplifier and point out how crossover distortion, thermal runaway,
and some of the minor problems can be handled.
Amplifier Design Procedure
In any power amplifier design the governing factors will be the desired power
output, available voltage, and component efficiency. Assuming that we wish to be
able to deliver 8 watts to the loudspeaker, we must first account for the losses
in the output transformer, which may be about 80 percent efficient. This immediately
brings the actual maximum power that the two transistors must deliver up to about
10 watts. If we want to allow for 25 percent overload capacity, the power is increased
to 12.5 watts or 6.25 watts per transistor. A typical supply voltage would be 12
volts which would permit operating the equipment direct from an automobile battery
or two 6volt lantern batteries. It would also be possible to build a well regulated
supply, using a standard 12.6volt filament transformer as power source.
Once the power and the voltage are determined, we can select a transistor type.
It must be able to handle at least 6.25 watts and must have a collectortoemitter
voltage rating of at least twice the supply voltage, which means 24 volts. For our
example we have selected the 2N301 which is made by RCA, Bendix, Sylvania, and CBS,
and is readily available at parts distributors. This transistor is rated at 40 volts
collector potential and can dissipate 11 watts at 80°C which means about 25 watts
at room temperature. These ratings are higher than our minimum requirements but
they afford us a much needed margin of safety.
To get an idea of what the peakcurrent swing per stage can be, we can calculate:
6.25 watts x (4 ¸ 12)
volts = 2.1 amps
The manufacturers' data shows that the 2N301 can handle up to 3 amps. peak current.
To get the load resistance per stage we divide the 12volt supply voltage by the
2.1 amp. peak current and this is roughly 6 ohms. One of the characteristics of
Class B pushpull circuits is the fact that the total primary impedance of the output
transformer is four times the load resistance per stage or 24 ohms in our example.
Fig. 1  Collector characteristics of 2N301.
Fig. 2  Transfer characteristics of 2N301.
Fig. 3  Base characteristics of the 2N301.
Fig. 4  Basic design of the 8·watt amplifier.
Fig. 5  The distortion due to the crossover.
Fig. 6  Prebias circuit for the amplifier.
At this point it is useful to study the characteristic curves of the transistor
in question. Fig. 1 shows the collector characteristics for the 2N301 for various
values of base current. The a.c. load line for the 6ohm load resistance is drawn
by connecting the 12volt, zerocurrent point to the 2.1amp., zerovoltage point.
To calculate maximum power handling ability we have accounted for 25 percent overload
capacity, but for normal operation the current and voltage swing will be limited
by a factor:
k = sqrt (1/1.25) = 0.896
Therefore, the normal fullload current swing will be only 2.1 amp. x 0.896 =
1.88 amp., as shown by the dotted line in Fig. 1. Another curve, Fig. 2,
shows the average transfer characteristic which is simply a plot of collector current
vs base voltage. For 1.88 amps. of collector current, the base voltage will have
to be 0.78 volt and this, on the base characteristic curve of Fig. 3, will
cause a base current of 34 ma. The product of 34 ma. x 0.78 volt is the input power,
26.5 mw.
The input impedance per transistor can be found by Ohm's Law from 0.78 volt divided
by 34 ma., or 23 ohms. We can now draw a basic diagram of the Class B amplifier
with its input and output requirements, as shown in Fig. 4. This simple circuit
will, however, suffer from the disadvantages inherent in Class B transistor amplifiers.
If we drive this amplifier with a sinewave signal of maximum amplitude, 0.78 volt
peak at the base of each stage, then the output signal at the loudspeaker will have
the waveform of Fig. 5A, which shows the typical symptoms of crossover distortion.
Crossover Distortion
Fig. 5 illustrates one of the most frequent defects in Class B transistor
amplifiers and the technician working with these circuits will soon become quite
familiar with the appearance of these distorted output signals, To understand the
cause for crossover distortion we need only look at the average transfer characteristic
curve of Fig. 2 and study the lower portion of the curve below 0.2 volt of
base bias. Here the curve flattens out and stops completely at 0.13 volt. This means
that from about zero to 0.13 volt of base signal, no current flows in the collector
circuit. When the base signal is very small the collector signal will take the form
of the curve of Fig. 5B, with current flowing only during that portion of the
sine wave which corresponds to more than 0.13 volt of base voltage. Since the two
pushpull transistors have the same characteristics, the distortion will be balanced
about the zero line of the sinewave signal.
To overcome this trouble it will be necessary to prebias each transistor slightly.
In effect, for small signals, the transistors then operate as Class A amplifiers.
This method can completely eliminate crossover distortion but it means that each
transistor draws some current at all times and this reduces the efficiency of the
Class B stages. In a good design, the prebias voltage is set carefully to minimize
the quiescent collector current.
Returning to the design of Fig. 4, we can see two places where a prebias
might be inserted. We could insert an additional battery between ground and the
two emitters or, and this is the simpler approach, we can utilize a portion of the
12volt collector supply to bleed a small negative voltage to the two bases. This
will cause a loss in input signal due to the impedance or the biasing network. In
a circuit of this type the bias resistors cannot be bypassed because the capacitor
would charge up to the signal voltage level and this would increase the fixed bias
too much.
The 2N301 characteristic curves of Figs. 2 and 3 indicate that a prebias of
about  0.13 volt is required. Previously we calculated the peak input impedance
to be about 23 ohms. The bias resistor should usually be about three times as large
so we select a value of 68 ohms, a readily available and standard unit. By using
Ohm's Law we find the current through the resistor to be 1.91 ma. At 0.13 volt the
base current itself is practically zero so that only about 2 ma. will flow in the
bias resistor. Because of the variations among individual transistors and other
circuit constants, it is advisable to include a potentiometer in the bias voltage
divider and set the actual voltage level for minimum collector current, commensurate
with minimum crossover distortion.
Looking at the revised circuit of Fig. 6, we can now see that the input
power of 26.5 mw. which we calculated previously will not be sufficient because
the actual input impedance, per stage, is not now 23 ohms but a total of 91 ohms.
The ratio between the I^{2}R input power for equal current is simply the
ratio of 23 and 91 ohms, which is 3.95. This corresponds to approximately 6 db,
the increase in input needed to overcome the effect of the prebiasing network.
The input power required to drive the circuit of Fig. 6 for peak output is,
therefore, 105 mw. Accounting for transformer losses of 20 percent, we find that
the actual peak driving power delivered by a driver amplifier to the primary of
the input transformer will have to be about 135 mw.
Driving circuits for Class B power amplifiers deserve a lengthy article in themselves,
but in this limited space we can only point out that Class A singlestage amplifiers
or Class A pushpull circuits are usually used in this application. There are a
number of circuits which avoid the use of a driving transformer and provide phase
splitting and impedance matching directly. For the example cited here it would be
possible to use a singlestage Class A 2N301 as driver or else a Type 2N32, 2N44,
or 2N226, all suitable and readily available from jobber stocks. The prime requirement
of a driver stage is power handling ability. If the reader refers to last month's
article on Class A power amplifiers, all of the circuit designs can be followed
except that the Class B pushpull stage input impedance must be substituted for
the load on the output transformer secondary.
Thermal Runaway
One of the basic facts about semiconductor physics is the interdependence of
current flow and temperature. As the temperature goes up, more current flows. As
current flows, heat is generated in the transistor. These two facts impose a severe
restriction on the circuit designer, especially when germanium transistors are used
where the critical temperatures are relatively close to room temperature. Silicon
devices have a somewhat higher critical temperature. The transistor characteristic
curves of Figs. 1, 2, and 3 all bear the notation "mounting flange temperature 25°C"
and this means that at a higher or lower temperature the characteristics shown may
be changed somewhat.
If a transistor were 100 percent efficient it would have no power loss in the
transistor itself but such a device is, of course, unavailable. The2N301, according
to the published data, will dissipate 3 watts for an output of 12 watts in a Class
B pushpull circuit. The 3 watts of heat must be conducted away from the transistor
or else it will build up to a progressively higher temperature. If the flange temperature
increases, the current through the collector increases and the amount of power which
is dissipated in the transistor also increases. In other words, if the mounting
arrangement of the transistor cannot dissipate 3 watts of power, the resulting temperature
buildup will burn out the transistor. It is possible, by careful design, to mount
each transistor so that it can easily radiate 3 watts into the surrounding air,
but on a hot day the efficiency of this heat transfer will suffer because the surrounding
air itself is warmer.
In last month's article on Class A power amplifiers we illustrated several techniques
for mounting power transistors for maximum heat radiation. The same approach should
be used for Class B pushpull circuits except that we must be careful not to allow
the heat from one transistor to contribute to the other, unless the dissipation
from both can be radiated readily.
In addition to the mechanical mounting methods, there are simple electronic means
of preventing thermal runaway and maintaining stability with varying temperatures.
The most widely used method involves base bias control by means of a temperaturesensitive
resistor or "thermistor." A thermistor can either increase or decrease in resistance
with temperature, but the latter type is more common. In using a thermistor to control
the bias of a transistor the thermistor is mounted close to the transistor heat
sink so that any heat rise in the transistor will affect the resistance of the thermistor.
Fig. 7  The final, practical circuit employed.
Returning once again to our example of a typical Class B pushpull circuit we
can see how a thermistor is used in the circuit of Fig. 7. Here the thermistor,
R_{T}, part of the bias network and in parallel with the 210ohm carbon
resistor, provides the desired 68 ohms at 25°C. When the temperature increases to
50°C the thermistor will be only 40 ohms and this will reduce the prebias enough
to cut the transistor collector current down to a safe value.
The principle is simply to reduce bias as temperature goes up and to do this
in conformity with the transistor characteristics. If the right thermistor were
used, the fixed resistance R_{1} would not be required, but most commercially
available thermistors are more temperature sensitive than needed and therefore a
fixed shunting resistor is often used.
Transformer Considerations
Before we can build the final circuit of Fig. 7, we must give some thought
to the two transformers. These items must be selected from available stock types
and, if a perfect match is not possible, the effects of mismatch will have to be
evaluated. Starting at the output stage, we immediately know that this transformer
will have to be the bigger one since it must handle at least 8 watts. Actually a
10watt unit will be the standard size. In checking through the catalogue we find
that a number of manufacturers make suitable units of this type. To cite just one,
consider the Triad TY29X. It has a centertapped primary with an impedance of 24
ohms and a secondary with either 8 or 4ohm impedances. It can handle 10 watts
of audio power. We can see that it meets our requirements exactly.
There are a number of other transformers equally suitable, such as the Stancor
T14 or Chicago TAMS12. It may happen that in another design the calculated output
impedance turns out to be a value which cannot be matched by a commercial output
transformer. We can then use the nearest available transformer type or change the
design of our circuit. The first method is recommended when the nearest available
transformer impedance is not more than 25 percent higher than the transistor output
impedance. Otherwise it is possible to change the output impedance by redrawing
the load line. We can change either the supply voltage or the peak power and, if
necessary, select a different transistor type.
When we consider the input transformer we see that, as far as the Class B amplifier
is concerned, we can select only the secondary and the power ratings. In our example
the input transformer must be capable of handling at least 135 mw. and must match
the input impedance of 182 ohms. Actually, to minimize distortion, the source impedance
should be lower than the input impedance so we should select a transformer which
has less than 182 ohms secondary impedance. A good choice would be the Thordarson
TR64 which has a 100ohm centertapped secondary and a primary impedance of 100
ohms. It can handle 0.5 watt which is ample for this circuit. Because the secondary
impedance is lower, some loss in power transfer will occur here which means that
the driver stage will have to deliver more than the 135 mw. previously calculated.
In a conservative design the driver stage will be capable of delivering at least
twice the driving power calculated for the Class B output stages.
Conclusion
Class B transistor amplifiers have the great advantage of requiring almost no
quiescent power and are, therefore, very efficient. The design principles are the
same as for vacuumtube pushpull Class B circuits, except that the transistor's
temperature characteristics must be taken into account. The detailed design procedure
presented here requires only a knowledge of Ohm's Law, arithmetic, and an understanding
of characteristics curves.
Posted October 8, 2021(original
1/3/2013)
